PX4 User Guide

# Offboard Mode

The vehicle obeys a position, velocity or attitude setpoint provided over MAVLink. The setpoint may be provided by a MAVLink API (e.g. MAVSDK or MAVROS) running on a companion computer (and usually connected via serial cable or wifi).

Note

  • This mode requires position or pose/attitude information - e.g. GPS, optical flow, visual-inertial odometry, mocap, etc.
  • RC control is disabled except to change modes.
  • The vehicle must be armed before this mode can be engaged.
  • The vehicle must be already be receiving a stream of target setpoints before this mode can be engaged.
  • The vehicle will exit the mode if target setpoints are not received at a rate of > 2Hz.

# Description

Offboard mode is primarily used for controlling vehicle movement and attitude, and supports only a very limited set of MAVLink messages (more may be supported in future).

Other operations, like taking off, landing, return to launch, are best handled using the appropriate modes. Operations like uploading, downloading missions can be performed in any mode.

A stream of setpoint commands must be received by the vehicle prior to engaging the mode, and in order to remain in the mode (if the message rate falls below 2Hz the vehicle will stop). In order to hold position while in this mode, the vehicle must receive a stream of setpoints for the current position.

Offboard mode requires an active connection to a remote MAVLink system (e.g. companion computer or GCS). If the connection is lost, after a timeout (COM_OF_LOSS_T) the vehicle will attempt to land or perform some other failsafe action. The action is defined in the parameters COM_OBL_ACT and COM_OBL_RC_ACT.

# Supported Messages

# Copter/VTOL

  • SET_POSITION_TARGET_LOCAL_NED

    • The following input combinations are supported:
      • Position setpoint (only x, y, z)
      • Velocity setpoint (only vx, yy, vz)
      • Thrust setpoint (only afx, afy, afz)

        Note Acceleration setpoint values are mapped to create a normalized thrust setpoint (i.e. acceleration setpoints are not "properly" supported).

      • Position setpoint and velocity setpoint (the velocity setpoint is used as feedforward; it is added to the output of the position controller and the result is used as the input to the velocity controller).

  • SET_POSITION_TARGET_GLOBAL_INT

    • The following input combinations are supported:
      • Position setpoint (only lat_int, lon_int, alt)
      • Velocity setpoint (only vx, yy, vz)
      • Thrust setpoint (only afx, afy, afz)

        Note Acceleration setpoint values are mapped to create a normalized thrust setpoint (i.e. acceleration setpoints are not "properly" supported).

      • Position setpoint and velocity setpoint (the velocity setpoint is used as feedforward; it is added to the output of the position controller and the result is used as the input to the velocity controller).

  • SET_ATTITUDE_TARGET

    • The following input combinations are supported:
      • Attitude/orientation (SET_ATTITUDE_TARGET.q) with thrust setpoint (SET_ATTITUDE_TARGET.thrust).
      • Body rate (SET_ATTITUDE_TARGET .body_roll_rate ,.body_pitch_rate, .body_yaw_rate) with thrust setpoint (SET_ATTITUDE_TARGET.thrust).

# Fixed Wing

  • SET_POSITION_TARGET_LOCAL_NED

    • The following input combinations are supported (via type_mask):
      • Position setpoint (only x, y, z)

        • Specify the type of the setpoint in type_mask (if these bits are not set the vehicle will fly in a flower-like pattern):

          Note The setpoint type values below are not part of the MAVLink standard for the type_mask field.

          The values are:

          • 4096: Takeoff setpoint.
          • 8192: Land setpoint.
          • 12288: Loiter setpoint (fly a circle centred on setpoint).
          • 16384: Idle setpoint (zero throttle, zero roll / pitch).
    • PX4 supports the coordinate frames (coordinate_frame field): MAV_FRAME_LOCAL_NED and MAV_FRAME_BODY_NED.

  • SET_POSITION_TARGET_GLOBAL_INT

    • The following input combinations are supported (via type_mask):
      • Position setpoint (only lat_int, lon_int, alt)

        • Specify the type of the setpoint in type_mask (if these bits are not set the vehicle will fly in a flower-like pattern):

          Note The setpoint type values below are not part of the MAVLink standard for the type_mask field.

          The values are:

          • 4096: Takeoff setpoint.
          • 8192: Land setpoint.
          • 12288: Loiter setpoint (fly a circle centred on setpoint).
          • 16384: Idle setpoint (zero throttle, zero roll / pitch).
    • PX4 supports the coordinate frames (coordinate_frame field): MAV_FRAME_GLOBAL.

  • SET_ATTITUDE_TARGET

    • The following input combinations are supported:
      • Attitude/orientation (SET_ATTITUDE_TARGET.q) with thrust setpoint (SET_ATTITUDE_TARGET.thrust).
      • Body rate (SET_ATTITUDE_TARGET .body_roll_rate ,.body_pitch_rate, .body_yaw_rate) with thrust setpoint (SET_ATTITUDE_TARGET.thrust).

# Rover

  • SET_POSITION_TARGET_LOCAL_NED

    • The following input combinations are supported (in type_mask):
      • Position setpoint (only x, y, z)

        • Specify the type of the setpoint in type_mask:

          Note The setpoint type values below are not part of the MAVLink standard for the type_mask field.

          The values are:

          • 12288: Loiter setpoint (vehicle stops when close enough to setpoint).
      • Velocity setpoint (only vx, yy, vz)

  • SET_POSITION_TARGET_GLOBAL_INT

    • The following input combinations are supported (in type_mask):
      • Position setpoint (only lat_int, lon_int, alt)
    • Specify the type of the setpoint in type_mask (not part of the MAVLink standard). The values are:
      • Following bits not set then normal behaviour.
      • 12288: Loiter setpoint (vehicle stops when close enough to setpoint).

  • SET_ATTITUDE_TARGET

    • The following input combinations are supported:
      • Attitude/orientation (SET_ATTITUDE_TARGET.q) with thrust setpoint (SET_ATTITUDE_TARGET.thrust).

        Note Only the yaw setting is actually used/extracted.

# Offboard Parameters

Offboard mode is affected by the following parameters:

Parameter Description
COM_OF_LOSS_T Time-out (in seconds) to wait when offboard connection is lost before triggering offboard lost failsafe (COM_OBL_ACT and COM_OBL_RC_ACT)
COM_OBL_ACT Mode to switch to if offboard control is lost when not connected to RC (Values are - 0: Land, 1: Hold, 2: Return ).
COM_OBL_RC_ACT Mode to switch to if offboard control is lost while still connected to RC control (Values are - 0: Position, 1: Altitude, 2: Manual, 3: Return , 4: Land).
COM_RC_OVERRIDE If enabled for offboard mode, stick movement immediately gives control back to the pilot (switches to Position mode).

# Developer Resources

Typically developers do not directly work at the MAVLink layer, but instead use a robotics API like MAVSDK or ROS (these provide a developer friendly API, and take care of managing and maintaining connections, sending messages and monitoring responses - the minutiae of working with Offboard mode and MAVLink).

The following resources may be useful for a developer audience:

← Terrain Following/Holding →